The Ultimate Guide To Drilling Porcelain Tile

The installation of porcelain tile is turning into an more and more normal undertaking for the current day tiler. clients preference the look of natural stone, however require the greater durability that porcelain tiles provide. With porcelain tiles being non-porous (impervious to water) and sincerely renovation loose, they’re the suitable answer for the regularly popular wet-room styled bathrooms.

With porcelain being one of the maximum popular picks of tile fabric available, and with the fashion for porcelain tile set to maintain, tilers have had to adapt their working techniques and tools if you want to cater for the demands of their clients. until lately, a massive variety of tile fixers have shied away from the set up and drilling of porcelain tiles due its perceived trouble.

however, drilling holes in porcelain tile isn’t hard! the usage of the appropriate methods and the first-rate gear for the activity, it’s far possible to obtain perfect cuts in a depend of seconds.

encouraged system for Drilling Porcelain Tile

high first-class diamond middle drill bits
Carbide pilot drill bit – only required in case you’re drilling big diameter holes (13mm or larger) and don’t have a appropriate-sized (8mm) diamond drill bit
Masonry drill bits – covered with quality tile drill bits
Water cooling gadget
electric powered drill clean protection glasses / goggles
RCD breaker
identifying the size of hollow to be Drilled
step one is to correctly identify the dimensions of hollow to be drilled. this is very important, as the diameter of the hole to be reduce dictates the technique that you will use to drill into the tile.

most of the people of holes which can be 10mm and below in diameter could be drilled with the tile already constant to the wall. Conversely, the majority of holes over 10mm in diameter could be drilled into the tile before the tile has been constant.You can get the best cordless drills 2017 reviews for more details.

best drills

when drilling holes that are 13mm or larger in diameter, make certain that the tile to be drilled is positioned in a tray to be able to accumulate the waste water that is produced. make sure that scrap tiles or another similar material is located underneath the tile this is being drilled. this could help to halt the development of the drill once it has finished drilling thru the tile.

earlier than drilling tile, make sure which you are wearing the right protection device, inclusive of safety glasses or goggles. make certain that you are the usage of a residual modern tool (RCD) to assist prevent electric powered surprise.

Drilling Small Diameter Holes (10mm or Smaller) with Diamond Cores

1. Mark the center of the hollow to be drilled into the tile via using a marker or a sticky drive pad.

2. connect the precise diamond center bit to the electrical drill and make sure that there is a steady deliver of cold water this is being directly geared toward the diamond core i.e. via the use of water cooling equipment.

notice regarding water cooling… it is important to ensure that there may be a constant supply of bloodless water directed on the drill bit so that it will keep the diamond core cool and to assist get rid of any debris which can have constructed up whilst drilling the tile. It is not advisable to attempt and cool the diamond drill bit by means of the use of a handheld aspirator or drilling via a moist sponge. these methods will no longer hold the drill bits cool enough, and will significantly shorten the lifestyles of the drill bit.

three. make certain that the drill is in “regular” mode and set the drill to among a thousand and 1500 rpm. when you have marked the tile with a marker it is fine to drill into the tile using a way known as “leaning in”. “Leaning in” guarantees that the drill will not slip and wander off center as you begin to drill into the tile.

the way to “lean in”… To “lean in”, actually start the drill at an attitude, as quickly as the drill bit has started to reduce the tile, slowly carry the drill right into a vertical function. make certain that sufficient pressure is being carried out (tile dust ought to be evident in cooling water) and rotate slowly till you’ve got cut the precise hollow. As you finish the hollow, you may notice that the tone of the drill will trade.

using sticky force pads… in case you use a sticky drive pad, it is needless to use the “leaning in” approach. without a doubt begin the drill in a vertical function and the sticky pad will make certain that the drill does not slip. as soon as you’ve got completed drilling the tile, in reality peel off the sticky pressure pad.

4. due to the fact most of the people of small diameter holes can be reduce into tiles already fixed to the wall, it’ll be essential to drill a fixing hollow at the back of the tile. replace the diamond core with the appropriately sized masonry drill bit and set the drill to “hammer” mode. Use a sluggish speed for drilling into hard substances to ensure that the tip does not overheat. make sure that the drill bit is regularly withdrawn in an effort to stop a increase of dirt.

Drilling Small Diameter Holes (10mm or Smaller) with Carbide Bits

1. first off, mark in which the hollow will be drilled, at the tile, the usage of a marker.

2. connect a carbide drill bit in your drill. ensure that there is a constant supply of bloodless water this is being at once aimed at the chosen drill bit i.e. by means of the usage of water cooling device.

word regarding water cooling… it’s miles vital to ensure that there may be a consistent deliver of cold water, with a view to keep the drill bit cool and to assist get rid of any particles that may have constructed up while drilling the tile. It isn’t always really helpful to attempt and cool the drill bit with the aid of using an aspirator or drilling through a wet sponge, those methods will not keep the drill bit cool enough, and the drill bit will burn out.

3. Set the electrical drill to between 700 and 900 rpm. make sure that the drill is in “normal” mode.

four.Push the carbide drill bit lightly into where you have marked the tile till you hear a cracking sound. start drilling from a vertical role with enough pressure and don’t forestall till you pay attention a change inside the tone of the drill. As soon as you hear the change inside the tone, begin to ease off.

5. because most people of small diameter holes may be reduce into tiles already fixed to the wall, it’ll be necessary to drill a fixing hole in the back of the tile. update the carbide drill bit with the correctly sized masonry drill bit and set the drill to “hammer” mode. Use a slow pace for drilling into hard materials to ensure that the end does not overheat. make sure that the drill bit is often withdrawn with a purpose to stop a increase of dust.

Drilling large Diameter Holes (13mm or large)

1. a good way to cut holes which might be 13mm or larger in diameter, it’s far essential to first drill a pilot hole. The pilot hole will act as a locater for a big diamond center and will assist you to drill a great hole in porcelain tile.

2. connect an 8mm carbide drill bit or 8mm diamond bit on your drill. comply with the commands given above for both “Drilling Small Diameter Holes (10mm or Smaller) with Diamond Cores” or “Drilling Small Diameter Holes (10mm or Smaller) with Carbide Bits”, relying on whether or not you are the usage of diamond cores or carbide drill bits. leave out the final step in both case as you might not be drilling a fixing hollow behind the tile.

three. Now that the pilot hole has been reduce, it’s far possible to drill the main (massive) hole. connect the suitable diamond center and ensure that there is a regular supply of bloodless water (see water cooling records inside the previous sections of this text).

4. Diamond cores which might be larger than 13mm will require an adapter with pilot pin that locates into the pilot hole that has been cut formerly, to make sure the perfect hole can be made.

five. starting the drill vertically, begin to drill in a circular motion with sufficient stress till the tone of the drill adjustments. Drilling holes into porcelain tile must take seconds no longer mins. If it’s miles taking you minutes, it’s far probably which you aren’t making use of sufficient stress or that you are the usage of an incorrect setting at the power device. See video beneath.

Comments are closed.

Post Navigation